Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
Four Wire Modem for SEL Mirrored-Bits
MBT 9600
Application specific features set the MBT9600 Four Modem apart from the conventional high speed modems. Its compact size and ease of installation make the MBT9600 an ideal, low cost alternative to conventional audio tone teleprotection systems.The circuitry is ideally suited for use over private networks such as conventional voice channels over analog microwave.
-
product
AC Current Isolated Sensor Two / Four Wire Transducer
TSCT (Average Sensing) / TFCT (TRUE RMS)
Kusam Electrical Industries Limited
• Transform Input: AC 5~400A directly into DC 4~20mA, no need external CT.• Suitable for application with high waveform distortion :(Frequency converter, Motor, SCR )• High accuracy ＜0.5%• High response time• High stability, easy connection.
-
product
Wide Jaw Kelvin Lead Set
6730
Wide Jaw Kelvin Lead Set. True wire four wire lead set with gold plated alligator clips that open to a wide .800? (20.3mm).
-
product
High-Accuracy Meter
Shenzhen Star Instrument Co., Ltd.
Three-phase four wire CT/VT meter provides unparalleled accuracy and measures forward/reverse active and reactive energy as well as four-quadrant reactive energy.
-
product
PXI-2530B, 128-Channel, 1-, 2-, or 4-Wire PXI Multiplexer Switch Module
778572-30
128-Channel, 1-, 2-, or 4-Wire PXI Multiplexer Switch Module—The PXI‑2530B is a high-density, multiconfiguration reed-relay switch. With four multiplexer and three matrix configurations, the PXI‑2530B is an excellent solution for complex or high‑channel‑count systems. Multiplexer configurations include 128x1 (1‑wire), 64x1 (2‑wire), 32x1 (4‑wire), or eight banks of 16x1 (1‑wire). Matrix configurations include 4x32 (1‑wire), 8x16 (1‑wire), or 4x16 (2‑wire). You can implement these configurations by selecting the appropriate terminal block.
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 8 Channel
50-200-008
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
product
RTD Measurement for VMEbus
VME390
The VME390 features 24 two, three or four wire high-accuracy PT100 measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued.
-
product
Relay Test Jumper Kit
56810
Set includes four jumpers to fit the most popular size relays on domestic and import vehicles. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using green four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on. Set comes in blow-molded case for storage.
-
product
Three Phase Meter Test Bench
Supreme Instrument Laboratories
Three phase meter test bench suitable for calibration & testing of AC Ammeters, Voltmeters, Single phase Energy Meters, Watt Meters, Power Factor Meters, Three Phase Two Wire & Three Phase Four Wire Energy Meters Trivector Meters, Maximum demand indicators, of active & reactive systems, Three phase 3 wire & 4 wire watt meters, Var Meters, Power Factor Meters etc.
-
product
Contact Resistance Meter
4.5 Digits LED display Range : 0 TO 1999.9 W to 199.99mW High Measurement Current : 100A DC max. True Four wire resistance measuring technique eliminates lead resistance errors inherent in 2 wire systems. Fully protected against overloads. Proven design
-
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (CableEye®)
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination. Each contains four 16-pole screw terminal blocks that will accept bare wires from 12- to 30-gauge in size. The metal jaws firmly grip an inserted wire without damaging or distorting the end, and the space between each terminal block may be used as a wire channel to guide wires neatly to the side. For each channel, a pair of holes is provided through which wire ties may be inserted to hold the wire bundles in place.
-
product
Relay Test Jumper Kit II
60610
Set includes four jumpers to fit many popular relays on Honda, Nissan, Toyota, newer Ford and GM mini micro relays as well as International trucks. Set comes in blow-molded case for storage. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using grey four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on.
-
product
SoftLine
When connecting two Network Interfaces together over a network or over the Internet, a virtual four wire audio line is created. Along with the audio line you get an RS232 connection and some I/O-ports.
-
product
SparkFun Load Sensor Combinator
The SparkFun Load Sensor Combinator is a bare PCB that combines four load sensors into a standard four-wire Wheatstone bridge configuration. If you open up an electronic bathroom scale, you’ll find a large rat's nest of wires. The Load Sensor Combinator was created to combine the 12 wires found in a bathroom scale into the standard four-wire Wheatstone bridge configuration.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
Automated Data Collection
Three-phase multifunctional static electricity meters AMT B0x-FxxTIIx are determined for measurement of active and reactive electric energy, instantaneous active power for consumption and supply, maximum demand, voltage, current and power factor in threephase four wires networks in diredct or indirect connection.
-
product
Mid Energy Counters
UEM1P5-4D R for RS485 Modbus RTU/ASCII communicationUEM1P5-D M for M-Bus communicationUEM1P5-4D E for Ethernet (Modbus TCP) communicationFor 1 or 5A CTProgrammable CT ratioFully bi-directional four quadrants measurements for all energies and powersFor 3 / 4 wire networks with balanced or unbalanced load (UEM1P5-4D R and UEM1P5-4D E only for 4 wire networks)Class B according to EN 50470-3S0 output for energy pulse emissionAvailable with MID certification
-
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
product
AC Power Calibrator
LS3300
The LS3300 is an AC signal generator capable of outputting both current and voltage simultaneously, thus allowing it to calibrate power meters. Providing output ranges of 10mV-1250V, and 0.3 mA to 62.5 A, and upto 78.125 kW, the unit is capable of calibrating up to 0.15 % Class Power meters. New features on the LS3300 include a high definition LCD display, a vector diagram, and the ability to synchronize up to three units to emulate anything from single phase two wire to three phase four wire systems.
-
product
Low Cost Precision Shunt
LPS
This is a precision metal clad resistor designed with four terminals. These models exhibit a high load capacity as well as excellent accuracy. The isolated voltage and current connections make them suitable for very precise current measurements. Direct attachment to current bus and connection to voltage using flexible wires enables easy current measurement.
-
product
Circuit Tracer Open/Closed
SureTrace™ 955
Receiver display rotates automatically for easy viewingIdentifies breakers and fuses with CertainCircuit™ detection*Pinpoints open and shorts*Traces wires*0-99 display of signal strength*Audible indication intensifies in tone/pitch with signal strength*Works on energized or de-energized circuits (0-600V AC/DC)*Four sensitivity levels*Peak reading bar graph*2-year warranty
-
product
Mini Back Probes/Wire Piercers
618
*Great for backprobing weather pack style connectors used with numerous automotive sensors *Also very handy for piercing and tapping readings on smaller gauge wires - using the included probe adapters *Works with most Test Lead Kits in the field - with standard 4mm banana plug test lead *Set includes four probes - red, black, green, yellow Test probes 21 mm length
-
product
ABex Terminal Module for Göpel 1149Cx BSCAN Cards
ABex TM-1149Cx
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
product
Milli Ohm Meter
Teledyne Test Tools series of D.C. Milli-Ohm meters offer two models T3MIL50 and T3MIL50X, which features a 3.5-inch TFT display with a measurement accuracy of 0.05%, maximum 50,000 count measurement display and sampling rate of 60 readings per second. The T3MIL series also provides four wire measurement as well as temperature measurement and temperature compensation functions to meet the requirements of low resistance measurement applications.
-
product
64 Channel 12C GPIO Expansion
FXA-102 I2C Expander
The FXA-102 provides 64bit of General-Purpose Input / Output (GPIO) which are controlled via I2C. It is 3,3V and 5V compatible and based on four 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. Using the optional Phoenix Contact UMK housing, the FXA-102 can be installed on a DIN rail. The dual row 2,54mm pin headers allow usage with IDC20 connectors or wire wrap cables.
-
product
ABex Terminal Module for Göpel 1149Cx-FXT BSCAN Cards
ABex TM-1149Cx-FXT
The ABex TM-1149Cx-FXT is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C4-FXT-X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan card it’s possible to connect up to four JTAG/Boundary Scan TAPs. All differential signal wires on the PCB are impedance controlled. In addition, all other digital signals (PIP, TRG, Aux, I/O) and Ground can be switched off via relays.
